Wireless-New
| Line 248: | Line 248: | ||
</nowiki> | </nowiki> | ||
==Apparently working with VLANs and public ssid== | ==Apparently working with VLANs and public ssid== | ||
# Process, copy the config below, edit it to replace the AP name and BVI address to match. Set the passwords | |||
#Connect to the AP via the console port | |||
# `enable` to get control | |||
# `write erase` to clear the existing config | |||
# `reload` confirm when promted. You do not want to copy any changes if asked | |||
# when the AP has restarted, once again `enable` | |||
# `conf t` to enter config mode | |||
# paste in your config | |||
# `write mem` to save the config | |||
# wait for about a minute you should see chatter about the radio doing things | |||
<nowiki> | <nowiki> | ||
hostname PDAP-18 | hostname PDAP-18 | ||
| Line 263: | Line 273: | ||
authentication key-management wpa | authentication key-management wpa | ||
mbssid guest-mode | mbssid guest-mode | ||
wpa-psk ascii | wpa-psk ascii ***** | ||
! | ! | ||
dot11 ssid PD_BACK | dot11 ssid PD_BACK | ||
| Line 269: | Line 279: | ||
authentication key-management wpa | authentication key-management wpa | ||
infrastructure-ssid | infrastructure-ssid | ||
wpa-psk ascii | wpa-psk ascii ***** | ||
! | ! | ||
dot11 ssid PD_PUBLIC | dot11 ssid PD_PUBLIC | ||
| Line 279: | Line 289: | ||
dot11 network-map | dot11 network-map | ||
dot11 guest | dot11 guest | ||
! | ! | ||
! | ! | ||
Revision as of 19:27, 21 April 2022
Configuration
| Cisco 1600 | |||
|---|---|---|---|
| Hostname | BVI IP | Location | Notes |
| PDAP-1 | 10.2.1.1 | ||
| PDAP-2 | 10.2.1.2 | ||
| PDAP-3 | 10.2.1.3 | ||
| PDAP-4 | 10.2.1.4 | ||
| PDAP-5 | 10.2.1.5 | ||
| PDAP-6 | 10.2.1.6 | ||
| PDAP-7 | 10.2.1.7 | ||
| PDAP-8 | 10.2.1.8 | ||
| PDAP-9 | 10.2.1.9 | ||
| PDAP-10 | 10.2.1.10 | ||
| PDAP-11 | 10.2.1.11 | ||
| PDAP-12 | 10.2.1.12 | ||
| PDAP-13 | 10.2.1.13 | ||
| PDAP-14 | 10.2.1.14 | ||
| PDAP-15 | 10.2.1.15 | ||
| PDAP-16 | 10.2.1.16 | ||
| PDAP-17 | 10.2.1.17 | ||
| PDAP-18 | 10.2.1.18 | ||
| PDAP-19 | 10.2.1.19 | ||
| PDAP-20 | 10.2.1.20 |
| Cisco 702W | |||
|---|---|---|---|
| Hostname | BVI IP | Location | Notes |
| PDAP-30 | 10.2.1.30 | ||
| PDAP-31 | 10.2.1.31 | ||
| PDAP-32 | 10.2.1.32 | ||
| PDAP-33 | 10.2.1.33 | ||
| PDAP-34 | 10.2.1.34 | ||
| PDAP-35 | 10.2.1.35 | ||
| PDAP-36 | 10.2.1.36 | ||
| PDAP-37 | 10.2.1.37 | ||
| PDAP-38 | 10.2.1.38 | ||
| PDAP-39 | 10.2.1.39 |
Config file 1600
Dot11 ssid PDCREW
authentication open
authentication key-management wpa
wpa-psk ascii ******
Guest-mode
Exit
Dot11 ssid PD_BACK
authentication open
authentication key-management wpa
wpa-psk ascii ******
infrastructure-ssid optional
Exit
Int dot11 0
world-mode dot11d country-code GB outdoor
speed range
power local maximum
encryption mode ciphers tkip
dot11 extension aironet
ssid PDCREW
Stat root access
No shut
Exit
Int dot11 1
world-mode dot11d country-code GB outdoor
speed range
power local maximum
encryption mode ciphers tkip
dot11 extension aironet
ssid PDCREW
ssid PD_BACK
station-role root access-point fallback repeater
No shut
Exit
Config file 702
Dot11 ssid PDCREW
authentication open
authentication key-management wpa
wpa-psk ascii ******
Guest-mode
Exit
Int dot11 0
world-mode dot11d country-code GB outdoor
speed range
power local maximum
encryption mode ciphers tkip
dot11 extension aironet
ssid PDCREW
Stat root access
No shut
Exit
Int dot11 1
world-mode dot11d country-code GB outdoor
speed range
power local maximum
encryption mode ciphers tkip
dot11 extension aironet
ssid PDCREW
station-role root access-point
No shut
Exit
VLAN attempt to give us PB_PUBLIC (WIP)
hostname PDAP-8 interface BVI 1 ip address 10.2.1.8 255.0.0.0 ex dot11 vlan-name BACKHAUL vlan 1 dot11 vlan-name CREW vlan 12 dot11 vlan-name PUBLIC vlan 13 bridge irb dot11 ssid PD_BACK vlan 1 authentication open authentication key-management wpa wpa-psk ascii ******** infrastructure-ssid ex dot11 ssid PDCREW vlan 12 authentication open authentication key-management wpa wpa-psk ascii ******* mbssid guest-mode ex dot11 ssid PD_PUBLIC vlan 13 mbssid guest-mode authentication open authentication key-management wpa wpa-psk ascii ******** mbssid guest-mode ex interface GigabitEthernet 0 no ip address no ip route-cache bridge-group 1 ex interface dot11Radio 0 world-mode dot11d country-code GB outdoor speed range power local maximum mbssid encryption vlan 13 mode ciphers tkip encryption vlan 12 mode ciphers tkip ssid PDCREW ssid PD_PUBLIC station-role root access-point no shut ex int dot11Radio 0.1 encapsulation dot1Q 1 native bridge-group 1 ex int dot11Radio 0.12 encapsulation dot1Q 12 bridge-group 1 ex int dot11Radio 0.13 encapsulation dot1Q 13 bridge-group 1 ex int dot11Radio 1.1 encapsulation dot1Q 1 native bridge-group 1 ex int dot11Radio 1.12 encapsulation dot1Q 12 bridge-group 1 ex int dot11Radio 1.13 encapsulation dot1Q 13 bridge-group 1 ex interface dot11Radio 1 world-mode dot11d country-code GB outdoor speed range power local maximum encryption vlan 1 mode ciphers tkip ssid PD_BACK station-role root access-point fallback repeater no shut ex bridge 1 protocol ieee bridge 1 route ip dot11 network-map
Apparently working with VLANs and public ssid
- Process, copy the config below, edit it to replace the AP name and BVI address to match. Set the passwords
- Connect to the AP via the console port
- `enable` to get control
- `write erase` to clear the existing config
- `reload` confirm when promted. You do not want to copy any changes if asked
- when the AP has restarted, once again `enable`
- `conf t` to enter config mode
- paste in your config
- `write mem` to save the config
- wait for about a minute you should see chatter about the radio doing things
hostname PDAP-18 ! ! ! dot11 syslog dot11 vlan-name BACKHAUL vlan 1 dot11 vlan-name CREW vlan 12 dot11 vlan-name PUBLIC vlan 13 ! dot11 ssid PDCREW vlan 12 authentication open authentication key-management wpa mbssid guest-mode wpa-psk ascii ***** ! dot11 ssid PD_BACK authentication open authentication key-management wpa infrastructure-ssid wpa-psk ascii ***** ! dot11 ssid PD_PUBLIC vlan 13 authentication open mbssid guest-mode ! ! dot11 network-map dot11 guest ! ! bridge irb ! ! ! interface Dot11Radio0 no ip address ! encryption vlan 1 mode ciphers tkip ! encryption vlan 12 mode ciphers tkip ! ssid PDCREW ! ssid PD_PUBLIC ! mbssid world-mode dot11d country-code GB outdoor speed range power local maximum station-role root access-point ! interface Dot11Radio0.1 encapsulation dot1Q 1 native bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.12 encapsulation dot1Q 12 bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.13 encapsulation dot1Q 13 bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio1 no ip address ! encryption mode ciphers tkip ! ssid PD_BACK ! world-mode dot11d country-code GB outdoor speed range power local maximum station-role root access-point fallback repeater bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto bridge-group 1 bridge-group 1 spanning-disabled no bridge-group 1 source-learning ! interface BVI1 ip address 10.2.1.18 255.0.0.0 no ip route-cache ! bridge 1 protocol ieee bridge 1 route ip ! interface dot11Radio 0 no shut interface dot11Radio 1 no shut interface BVI 1 no shut interface GigabitEthernet0 no shut end